- Osciloscopio tektronix multisim 12 generator#
- Osciloscopio tektronix multisim 12 series#
- Osciloscopio tektronix multisim 12 free#
First off connect a BNC T-connector to the sine wave oscillator’s output, which will essentially give your oscillator two outputs. Transient Analysis Output, Analysis Parameters ( ).Ĥ) ( ) DC-Sweep Analysis. You can calculate the phase shift by measuring the circuit’s input signal with your oscilloscope’s first channel and the circuit’s output with your scope’s second channel. ( ), (AC Sweep, DC Sweep, Transient Analysis. multipoint control unit)9) Advanced_Peripherals. , power sources (, ,, - VCC, VDD, VSS,VEE), signal voltage sources (, ), signal currentsourses (,, ) , Convergence Assistant, SPICE,Ĭtrl+N Ctrl+O Ctrl+S Ctrl+P / Ctrl+Z Ctrl+X Ctrl+C Ctrl+V Ctrl+D Circuit Description BoxCtrl+F Delete Ctrl+W Ctrl+J Ctrl+Q Ctrl+I Ctrl+B Ctrl+T F5 F6 Alt+Y Alt+X Ctrl+R 90 Ctrl+Shift ġ200 SPICE-, Analog Devices, LinearTechnology Texas Instruments, 100.
Osciloscopio tektronix multisim 12 free#
Find digital and analog oscilloscopes for sale in auctions, classifieds, free wanted ads. Multisim 10.0 National Instruments, NI ELVIS NI LabVIEW. Used oscilloscopes at LabX, buy and sell used test equipment online at LabX. Multisim 10.0 National Instruments LabVIEW,,. Complete equipment of simulation using LabView, Multisim, and MAX (easy. NI Multisim 10.0 Electronics Workbench Group National Instruments Multisim 10.0 Ultiboard 10.0, SPICE- . I am trying to make measurements of waveform of an oscilloscope Tektronix 1052 B. Specify the impedance as magnitude and phase, with the phase in degrees.1 3 3 Multisim4 5 6.10 12. Also calculate the impedance for the general impedance. Using the formulas for the impedance of each of the passive elements and the actual values of the elements, calculate the theoretical impedance for each element at each frequency where you made a measurement.
Osciloscopio tektronix multisim 12 series#
Finally, repeat the above procedure at all the frequencies where the DUT is a general impedance consisting of a 100 ohm resistor in series with a 100 mH inductor. luf capacitor as the DUT, and then the 100 mH inductor as the DUT. Repeat the above procedure at all the frequencies for the O. Osciloscopio con guía de compra para comprar el mejor osciloscopio, osciloscopio tektronix multisim 12. Lo que necesitas saber acerca de Osciloscopio tektronix multisim. sobre osciloscopio tektronix multisim 12 para que escojas el que más se adapte a ti.
Osciloscopio tektronix multisim 12 generator#
Use the voltage generator as the reference voltage, i.e., consider its phase value to be zero.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://http2.mlstatic.com/D_NQ_NP_894784-MLM45261729640_032021-F.jpg)
You will use this value to calculate the phase difference.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://i.ytimg.com/vi/TmnFGjMAO8E/maxresdefault.jpg)
Measure the time between 2 corresponding points on the 2 waveforms. Using the oscilloscope, measure the amplitude of the voltage V AC, and across the DUT (VBC).
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://http2.mlstatic.com/D_NQ_NP_831883-MLM46929347751_072021-F.jpg)
For ✓ set the generator to produce a 10 Hz sine wave, with an amplitude of 2 volts, RMS.Ĥ.
![osciloscopio tektronix multisim 12 osciloscopio tektronix multisim 12](https://i.ytimg.com/vi/1AyK7nsImc4/hqdefault.jpg)
that integrates 12 of the most commonly used instruments including the oscilloscope. Use the 1 KN resistor for the device under test (DUT). Complete integration with Multisim for circuits and electronics. PROCEDUREĪ 1ΟΚΩ B + V DUT DUT = Device Under Test Figure 1. NI Multisim e Ultiboard 12 NI LabVIEW 8.9 Mathworks Matlab R2011b Strumenti di misura e test. NOTE: in the simulation, use the simulated Tektronix TDS2024 oscilloscope when you need an oscilloscope. Insert At into one of the equations for y to get the phase in radians or degrees.